M24C64-RMB6TPA
AI

The **M24C64-RMB6TG** (often referred to within the M24C64 series) is a 64-Kbit serial I2C bus EEPROM (Electrically Erasable Programmable Read-Only Memory). It is widely used for parameter storage in consumer electronics, industrial applications, and medical devices.
### 1. Key Technical Specifications
| Parameter | Specification |
| :--- | :--- |
| **Memory Size** | 64 Kbits (8192 x 8 bits) |
| **Interface** | I2C (Serial 2-Wire) |
| **Clock Frequency** | 400 kHz (Fast Mode), 1 MHz (Fast Mode Plus) |
| **Supply Voltage (Vcc)** | 1.8V to 5.5V (Standard R range) |
| **Write Cycle Time** | 5 ms (Maximum) |
| **Endurance** | 4 Million Write Cycles |
| **Data Retention** | 200 Years |
| **Operating Temp** | -40°C to +85°C |
---
### 2. Pinout Configuration and Functions
The device typically comes in an 8-pin package (such as UFDFPN8 or TSSOP8).
* **E0, E1, E2:** Address inputs. These pins allow you to connect up to 8 M24C64 devices on the same I2C bus by hardware-coding their unique addresses.
* **SDA (Serial Data):** Bi-directional pin used to transfer data in and out of the device.
* **SCL (Serial Clock):** The clock input used to synchronize data transfer.
* **WC (Write Control):** A hardware protection pin. If connected to $V_{CC}$, write operations are inhibited (read-only mode). If connected to $V_{SS}$ (Ground), the entire memory is write-enabled.
* **Vcc/Vss:** Power supply and Ground.
---
### 3. Core Features
* **Byte and Page Write:** Supports writing a single byte or a full page of up to 32 bytes at once, which optimizes programming time.
* **Random and Sequential Read:** Data can be accessed from a specific address or read continuously from the current address.
* **Enhanced ESD Protection:** Designed to withstand high electrostatic discharge, making it robust for industrial environments.
* **Low Power Consumption:**
* Active Read current: < 1 mA.
* Standby current: < 3 µA (at 1.8V).
---
### 4. Part Number Breakdown (Suffix Logic)
The specific code **M24C64-RMB6TG** breaks down as follows:
| Code Segment | Meaning |
| :--- | :--- |
| **M24** | I2C Serial Access EEPROM |
| **C64** | 64 Kbit Density |
| **-R** | Voltage range: 1.8V to 5.5V |
| **MB** | Package: UFDFPN8 (Ultra thin fine pitch dual flat no lead) |
| **6** | Temperature: Industrial (-40 to +85 °C) |
| **T / P** | Tape & Reel Packing / Lead-free process |
---
### 5. Typical Application Circuit
```c
// Pseudo-code for writing to the M24C64
Start_I2C();
Send_Address(0xA0); // Device Address + Write Bit
Send_Word_Address(0x00); // Memory Address High Byte
Send_Word_Address(0x01); // Memory Address Low Byte
Send_Data(0x55); // Data to store
Stop_I2C();
```
- ⤷
How does the Write Control (WC) pin function differently from software write protection?
- ⤷ Can I use multiple M24C64 chips on the same I2C bus
- ⤷ and how is that addressed?
- ⤷ What are the advantages of using the UFDFPN8 package over the standard TSSOP8?