| Electronic Components Datasheet Search |
|
LM1770TMFX/NOPB Datasheet(PDF) 8 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM1770TMFX/NOPB Datasheet(HTML) 8 Page - Texas Instruments |
|
8 / 25 page ![]() VOUT fSW = D VOUT F = VIN x TON 1 TP = fSW VOUT D = VIN LM1770 SNVS403C – SEPTEMBER 2005 – REVISED APRIL 2013 www.ti.com APPLICATION INFORMATION THEORY OF APPLICATION The LM1770 synchronous buck switcher has a control scheme that is referred to as constant on-time control. This topology relies on a fixed switch on-time to regulate the output voltage. This on-time is internally set by EEPROM and is available with three different set-points to allow for different frequency options. The LM1770 automatically adjusts the on-time during operation inversely with the input voltage (VIN) to maintain a constant frequency. Therefore the switching frequency during continuous conduction mode is independent of the inductor and capacitor size unlike hysteretic switchers. At the beginning of the cycle the LM1770 turns on the high side PFET for a fixed duration. This on-time is predetermined (internally set by EEPROM and adjusted by VIN) and the switch will not turn off until the timer has completed its period. The PFET will then turn off for a minimum pre-determined time period. This minimum TOFF of 150ns is internally set and cannot be adjusted. This is to prevent false triggering from occurring on the comparator due to noise from the SW node transition. After the minimum TOFF period has expired, the PFET will remain off until the comparator trip-point has been reached. Upon passing this trip-point (set at 0.8V at the feedback pin), the PFET will turn back on and the process will repeat, thus regulating the output. The NFET control is complementary to the PFET control with the exception of a short dead-time to prevent shoot through from occurring. DEVICE OPERATION Timing Opinion Three versions of the LM1770 are available each with a predetermined TON set internally by EEPROM. This TON setting will determine the switching frequency for the application. Derivation and calculation of the switching frequency’s dependence on VIN and TON can be seen in the following section. In a PWM buck switcher the following equations can be manipulated to obtain the switching frequency. Equation 1 shows the standard duty-cycle equation given by the volts-seconds balance on the inductor with the following equations defining standard relationships: (1) TON = D x TP (2) (3) Using this equation and solving for duty-cycle: D = fSW x TON (4) Frequency can now be expressed as: (5) Or simply written as: (6) where, α = VIN x TON (7) To maintain a set frequency in an application, α is always held constant by varying TON inversely with VIN. The three versions of the LM1770 are identified by the on times at a VIN of 3.3V for consistency. For clarification see Table 2: Table 2. LM1770 "ON" Times Identification Product ID TON @ 3.3V α (V µs) LM1770S 0.5µs 1.65 LM1770T 1.0µs 3.3 8 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LM1770 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |