Electronic Components Datasheet Search
  Indian  ▼
ALLDATASHEET.IN

X  

H8S/2426R Datasheet(PDF) 420 Page - Renesas Technology Corp

Part # H8S/2426R
Description  16-Bit Single-Chip Microcomputer H8S Family / H8S/2400 Series
PDF  1302 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  RENESAS [Renesas Technology Corp]
Direct Link  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

H8S/2426R Datasheet(HTML) 420 Page - Renesas Technology Corp

Back Button H8S/2426R Datasheet HTML 416Page - Renesas Technology Corp H8S/2426R Datasheet HTML 417Page - Renesas Technology Corp H8S/2426R Datasheet HTML 418Page - Renesas Technology Corp H8S/2426R Datasheet HTML 419Page - Renesas Technology Corp H8S/2426R Datasheet HTML 420Page - Renesas Technology Corp H8S/2426R Datasheet HTML 421Page - Renesas Technology Corp H8S/2426R Datasheet HTML 422Page - Renesas Technology Corp H8S/2426R Datasheet HTML 423Page - Renesas Technology Corp H8S/2426R Datasheet HTML 424Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 420 / 1302 page
background image
Section 7 DMA Controller (DMAC)
Rev. 1.00 Sep. 19, 2008 Page 392 of 1270
REJ09B0466-0100
(6)
Activation Source Acceptance
At the start of activation source acceptance, a low level is detected in both
DREQ pin falling edge
sensing and low level sensing. Similarly, in the case of an internal interrupt, the interrupt request
is detected. Therefore, a request is accepted from an internal interrupt or
DREQ pin low level that
occurs before write to DMABCRL to enable transfer.
When the DMAC is activated, take any necessary steps to prevent an internal interrupt or
DREQ
pin low level remaining from the end of the previous transfer, etc.
(7)
Internal Interrupt after End of Transfer
When the DTE bit in DMABCRL is cleared to 0 at the end of a transfer or by a forcible
termination, the selected internal interrupt request will be sent to the CPU or DTC even if the
DTA bit in DMABCRH is set to 1.
Also, if internal DMAC activation has already been initiated when operation is forcibly
terminated, the transfer is executed but flag clearing is not performed for the selected internal
interrupt even if the DTA bit is set to 1.
An internal interrupt request following the end of transfer or a forcible termination should be
handled by the CPU as necessary.
(8)
Channel Re-Setting
To reactivate a number of channels when multiple channels are enabled, use exclusive handling of
transfer end interrupts, and perform DMABCR control bit operations exclusively.
Note, in particular, that in cases where multiple interrupts are generated between reading and
writing of DMABCR, and a DMABCR operation is performed during new interrupt handling, the
DMABCR write data in the original interrupt handling routine will be incorrect, and the write may
invalidate the results of the operations by the multiple interrupts. Ensure that overlapping
DMABCR operations are not performed by multiple interrupts, and that there is no separation
between read and write operations by the use of a bit-manipulation instruction.
Also, when the DTE and DTME bits are cleared by the DMAC or are written with 0, they must
first be read while cleared to 0 before the CPU can write 1 to them.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com